「太原快速门」堆积门防爆电机

「太原快速门」堆积门防爆电机的接线方法和注意事项


Wiring method and precautions of explosion-proof motor for stacking door of Taiyuan Express Gate

一说到快速门，相信大家并不陌生，再加上大家对安全意识的不断提升，大家对快速门防爆也有了进一步的需求，尤其是一些化工场所，粉尘、粉末比较多的地方，都要求快速门使用防爆型控制箱和电机。


Speaking of fast doors, I believe you are not unfamiliar with them. In addition to the increasing awareness of safety, there is a further demand for explosion-proof fast doors. Especially in some chemical sites, where there are more dust and powder, explosion-proof control boxes and motors are required for fast doors.


对于防爆电机的品牌和功能，我们在以前的文章中有过介绍，他们一般外形看起来比较厚重，但是防爆效果极佳，一下是接电注意事项


As for the brand and function of explosion-proof motors, we have introduced them in previous articles. Their general appearance looks thicker and heavier, but the explosion-proof effect is excellent. Here are the matters needing attention in connection with power supply.

「太原快速门」堆积门防爆电机的接线方法和注意事项


Wiring method and precautions of explosion-proof motor for stacking door of Taiyuan Express Gate


  1、快速门防爆电机安装与调试


1. Installation and debugging of explosion-proof motor for fast door


  a、为了保证人身安全，防爆卷帘门机、防爆控制器、防爆按钮等必须可靠接地。


A. In order to ensure personal safety, explosion-proof rolling shutter doors, explosion-proof controllers, explosion-proof buttons, etc. must be reliably grounded.

  b、安装调试及开关卷帘门时，严禁门下行人或站人。


B. When installing, debugging and switching the rolling shutter door, it is strictly forbidden for people who come down or stand at the door.


  c、防爆卷帘门必须有资质的专科人员安装。


C. Explosion-proof rolling shutter doors must be installed by qualified specialists.


  d、左右安装调整制动壳体，必须用手将手动装置压至底部螺丝对角锁紧。


D. When adjusting brake case is installed left and right, the manual device must be pressed to the bottom screw to lock diagonally.


  e、链条的松紧度，由机脚上的两个调节螺钉，调节链条的松紧度。调整完毕后，应锁紧机脚上的压脚螺母。


E. The tightness of the chain is regulated by two adjusting screw on the machine foot. After adjustment, the foot nut on the machine foot should be locked.


  f、安装调试防爆快速门电机前，请仔细阅读本说明书，以免操作不当，造成不用要的算是。


F. Before installing and debugging the explosion-proof shutter motor, please read this manual carefully so as to avoid improper operation and unnecessary calculation.


  综上所述，，我们可以清楚的知道快速门防爆电机适合于在出产、加工、处理、储存过程中发现或可能发现气体、粉尘等爆炸危险环境的工业设备中。要是需要，可以拨打太原龙盛门业客服电话，我们将13小时在线为您服务的。


In summary, we can clearly know that the explosion-proof motors for fast doors are suitable for industrial equipment which can find or possibly find gas, dust and other explosive dangerous environments in the process of production, processing, processing and storage. If necessary, you can call Taiyuan Longshengmen customer service telephone, we will serve you online for 13 hours.



  2、快速门防爆电机与电源电缆的连接

2. Connection of explosion-proof motor of fast door with power cable


  a、电源引入电缆的外径要与密封圈的外径相符，密封圈材料为橡胶XH-12，规格及尺寸可以根据引入电缆外径大小剥去密封圈同心圆。


A. The outer diameter of the cable introduced by the power supply should be in accordance with the outer diameter of the sealing ring. The sealing ring material is rubber XH-12. The concentric circle of the sealing ring can be stripped according to the size and size of the outer diameter of the cable introduced.


配合直径差不得大于2mm，当压紧接线后，应保证密封圈与电缆之间及接线盒之间无间隙，否则将失去隔爆机能。密封圈老化变质应及时更换


The difference of mating diameter should not be greater than 2 mm. When the connection is pressed, there should be no gap between the sealing ring and the cable and the junction box, otherwise the flameproof function will be lost. Seal ring aging and deterioration should be replaced in time


  b、「太原快速门」龙盛门业表示引入的电缆芯线要接在两弓形垫圈之间，注意芯线的飞刺不要突出，引入电缆还需接线压板和弓形垫圈压紧固定，，防止窜动。


B. "Taiyuan Express Gate" Longsheng Gate Industry said that the introduced cable cores should be connected between the two bow gaskets, pay attention to the Spurs of the cores should not be prominent, the introduction of cables also need to be tightened and fixed by the connection plate and bow gaskets, to prevent movement.
 

  c、接线盒一个进口，可以引入两根多芯电缆的接线盒，当引入一根多芯电缆只使用一个进口时另一个进线口的金属垫片不得拿掉否则将失去防爆机能。


C. One inlet of the junction box can introduce two multi-core cable junction boxes. When one multi-core cable is introduced and only one inlet is used, the metal gasket of the other inlet must not be removed or the explosion-proof function will be lost.


  d、内外接地螺栓应可靠接地


D. Internal and external grounding bolts should be grounded reliably